Scag Power Equipment GC-STWC-CS61V Instrukcja Użytkownika

MODEL GC-STWC-CS61VTHIS MANUAL CONTAINS THE OPERATINGINSTRUCTIONS AND SAFETY INFORMA-TION FOR YOUR SCAG ACCESSORY. READ-ING THIS MANUAL WILL PROVIDE

8GC-STWC-CS61V BLOWER HOUSING ASSEMBLY2006 GC-STWC-61V Blower Assembly35353547899101011111212131414141415151617181920212223242427272830313233343535373

9GC-STWC-CS61V BLOWER HOUSING ASSEMBLYRef. PartNo. Number Description27 04019-04 Nut, Serr. Flange 3/8-1628 04001-136 Bolt, Hex Head 3/8-16 x

10GC-STWC-CS61V BLOWER MOUNTING COMPONENTSUNDER SIDE OFVELOCITY-PLUSCUTTER DECK SHOWN23232824242525262616162527123456678910101112131415151617181920200

11GC-STWC-CS61V BLOWER MOUNTING COMPONENTS1 483227 Belt Cover, GC-61V2 04029-04 Wingnut, Plastic 3/8" Small3 483223 Cap, Square Vinyl4 04021-08 N

12GC-STWC-CS61V HOPPER COMPONENTSABC2008 CSHOPPEREXPLOD-STWC 11645151445435655617415054349315111405859251289344950 24342942274838531033616037193620493

13GC-STWC-CS61V HOPPER COMPONENTSRef. PartNo. Number Description1 483038 Hopper, GC-STC-CS2 482732 Door, GC-CS3 461626 Sweeper Weldment, GC-CS

14FRONT WEIGHT COMPONENTS25431

15FRONT WEIGHT COMPONENTSRef. PartNo. Number Description1 461097 Weight Assembly2 04001-117 Bolt, Hex Head 7/16-14 x 1-3/4"3 451517 Support Weldm

16GC-STWC-CS61V DECALS483402482275481327483391483392483393483044483392483391483393 MANUFACTURED UNDER ONE OR MORE OF THE FOLLOWING PA

LIMITED WARRANTY- COMMERCIAL ACCESSORYAny part of the Scag commercial accessory manufactured by Scag and found, in the reasonable judgment of Scag,to

FAILURE TO FOLLOW SAFE OPERATING PRACTICES MAY RESULT IN SERIOUS INJURY.* Keep all safety shields in place.* Before performing any maintenance or se

PART NO. 03236PRINTED 3-2007PRINTED IN USA© 2007SCAG POWER EQUIPMENTDIVISION OF METALCRAFT OF MAYVILLE, INCwww.scag.com

11. With the hopper door closed, engage the deckdrive.2. Proceed to mow until the hopper is full.A replacement manual is available from yourauthorized

23. When dumping the hopper into a disposal area:5. To clean the hopper debris screen;A. Disengage the deck drive and allow allmoving parts to come to

33.1 ASSEMBLY INSTRUCTIONS FOR 61" CUTTER DECK-NOTE-Use the illustrated parts list as a part numberreference when following the assemblyinst

412. Install the hopper mounting brackets to theoutside of the frame on the rear of the machine.See Figure 3-5.FIGURE 3-513. With help from an assista

514. Install the hose from the blower assemblyadapter to the hopper hood and secure using the8-1/2" clamps.15. Using the weight support bar (p/n

64.1 GRASS CATCHER REMOVAL INSTRUCTIONS2005 GC-STC removal art 2-ALoosenLockingBoltsRemoveMountingPinsRemoveMountingPinsLoosenLockingBolts1. Prep

75.1 MAINTENANCE CHART - RECOMMENDED SERVICE INTERVALS* Perform these maintenance procedures more frequently under extreme dusty or dirty conditions.