Scag Power Equipment GC-STWC-61 Instrukcja Użytkownika

OPERATOR’S MANUALOPERATOR’S MANUALOPERATOR’S MANUALOPERATOR’S MANUALOPERATOR’S MANUALMODEL GC-STWC-61VTHIS MANUAL CONTAINS THE OPERATINGINSTRUCTIONS A

8GC-STWC-61V BLOWER HOUSING ASSEMBLY2006 GC-STWC-61V Blower Assembly3535354789910101111121213141414141515161718192021222324242727283031323334353537383

9GC-STWC-61V BLOWER HOUSING ASSEMBLYRef. PartNo. Number Description27 04019-04 Nut, Serr. Flange 3/8-1628 04001-136 Bolt, Hex Head 3/8-16 x 1-

10GC-STWC-61V" BLOWER MOUNTING COMPONENTSUNDER SIDE OFVELOCITY-PLUSCUTTER DECK SHOWN2323282424252526261616252712345667891010111213141515161718192

11GC-STWC-61V" BLOWER MOUNTING COMPONENTSRef. PartNo. Number Description1 483227 Belt Cover, GC-61V2 04029-04 Wingnut, Plastic 3/8" Small3 4

12GC-STWC-61V BUCKET SUPPORT COMPONENTS (UPPER)1234468559999511516161616161618181313192014212122232324311153233332627282930323363735253135381715934457

13GC-STWC-61V BUCKET SUPPORT COMPONENTS (UPPER)Ref. PartNo. Number Description1 423302 Screen, Catcher Hood2 04090-02 Pop Rivet, 3/16 x .6523

14GC-STWC-61V BUCKET SUPPORT COMPONENTS (LOWER)STC 2008 BSC12111415161718192021222324413546784381267445FRAME951010ATO "A"3669"A"25

15GC-STWC-61 BUCKET SUPPORT COMPONENTS (LOWER)1 04090-02 Pop Rivet, 3/16 x .6522 482321 Seal, Hood3 423262 Tube, Upright4 04041-07 Flatwasher, 3/8-.39

16GC-STWC-V DECALS483402482275481327483391483392483393483044483392483391483393 MANUFACTURED UNDER ONE OR MORE OF THE FOLLOWING PATENT

LIMITED WARRANTY- COMMERCIAL ACCESSORYAny part of the Scag commercial accessory manufactured by Scag and found, in the reasonable judgment of Scag,to

FAILURE TO FOLLOW SAFE OPERATING PRACTICES MAY RESULT IN SERIOUS INJURY.* Keep all safety shields in place.* Before performing any maintenance or se

PART NO. 03230PRINTED 3-2007PRINTED IN USA© 2007SCAG POWER EQUIPMENTDIVISION OF METALCRAFT OF MAYVILLE, INC.WWW.SCAG.COM

11.1 INTRODUCTIONThis manual has been prepared to provide theinformation you need to correctly assemble, operate,and maintain this grass catcher. Rea

23.1 ASSEMBLY INSTRUCTIONS FOR 61"CUTTER DECK-NOTE-Use the illustrated parts list as a part numberreference when following the assemblyinstructio

37. Install the blower assembly to the mountingbracket and secure with the mounting pin.See Figure 3-4.8. Align the blower assembly with the discharge

417. Using the weight support bar as a guide, identifythe four corresponding mounting holes, and theexisting hardware that will need to be removed ino

5FIGURE 4-15. Loosen the locking bolts and remove the two (2)pins holding the hood assembly to the mountingposts on the rear of the machine. See Figu

65.1 MAINTENANCE CHART - RECOMMENDED SERVICE INTERVALS* Perform these maintenance procedures more frequently under extreme dusty or dirty condition

7NOTES