Scag Power Equipment GC-STC-CSV Instrukcja Użytkownika

MODEL GC-STC-CSVTHIS MANUAL CONTAINS THE OPERATINGINSTRUCTIONS AND SAFETY INFORMA-TION FOR YOUR SCAG ACCESSORY. READ-ING THIS MANUAL WILL PROVIDE YOU

8GC-STC-CSV 48" & 52" BLO WER HOUSING ASSEMBLY2005 GC V+ Blower Assembly4547454789910101111121213141414141515161718192021222324242727283

9GC-STC-CSV 48" & 52" BLO WER HOUSING ASSEMBLYRef. PartNo. Number Description27 04019-04 Nut, Serr. Flange 3/8-1628 04001-136 Bo

10GC-STC-CSV 48" & 52" BLO WER MOUNTING COMPONENTSUNDER SIDE OFVELOCITY-PLUSCUTTER DECK SHOWN2323282424252526261616252712345667891010111

11GC-STC-CSV 48" & 52" BLOWER MOUNTING COMPONENTSRef. PartNo. Number Description1 484380 Belt Cover, GC-STC2 04029-04 Wingnut, Plastic 3

12GC-STC-CSV HOPPER COMPONENTSABC2008 CSHOPPEREXPLOD-STWC 11645151445435655617415054349315111405859251289344950 24342942274838531033616037193620493321

13GC-STC-CSV HOPPER COMPONENTSRef. PartNo. Number Description1 483038 Hopper, GC-STC-CS2 482732 Door, GC-CS3 461626 Sweeper Weldment, GC-CS4 4

14FRONT WEIGHT COMPONENTS25431

15FRONT WEIGHT COMPONENTSRef. PartNo. Number Description1 461097 Weight Assembly2 04001-117 Bolt, Hex Head 7/16-14 x 1-3/4"3 451517 Support Weldm

16GC-STC-CSV DECALS483402482275481327483391483392483393483044483392483391483393 MANUFACTURED UNDER ONE OR MORE OF THE FOLLOWING PATEN

LIMITED WARRANTY- COMMERCIAL ACCESSORYAny part of the Scag commercial accessory manufactured by Scag and found, in the reasonable judgment of Scag,to

FAILURE TO FOLLOW SAFE OPERA TING PRACTICES MAY RESULT IN SERIOUS INJURY.* Keep all safety shields in place.* Before performing any maintenance or s

PART NO. 03234 Rev.01PRINTED 6-2011PRINTED IN USA© 2011SCAG POWER EQUIPMENTDIVISION OF METALCRAFT OF MAYVILLE, INCwww.scag.com

11. With the hopper door closed, engage the deckdrive.2. Proceed to mow until the hopper is full.A replacement manual is available from yourauthorized

23. When dumping the hopper into a disposal area:5. To clean the hopper debris screen;A. Disengage the deck drive and allow allmoving parts to come to

33.1 ASSEMBLY INSTRUCTIONS FOR 48" AND 52" CUTTER DECK-NOTE-Use the illustrated parts list as a part numberreference when following th

412. Install the hopper mounting brackets to theoutside of the frame on the rear of the machine.See Figure 3-5.FIGURE 3-513. With help from an assista

514. Install the hose from the blower assemblyadapter to the hopper hood and secure using the6-1/2" clamps.15. Using the weight support bar (p/n

64.1 GRASS CATCHER REMOVAL INSTRUCTIONS2005 GC-STC removal art 2-ALoosenLockingBoltsRemoveMountingPinsRemoveMountingPinsLoosenLockingBolts1. Prep

75.1 MAINTENANCE CHART - RECOMMENDED SERVICE INTERVALS* Perform these maintenance procedures more frequently under extreme dusty or dirty conditions.